How to Make a Bicycle Trailer
Contents
Bicycle Trailers
Introduction
In many developing countries people live in regions away from the main transport infrastructure. This means transport services are expensive Many villages in the South are not part of road networks and the lack of transport is a constraint on income generating activities such as taking produce to markets and acquiring equipment and materials needed for a small enterprise. The approach of Practical Action is to promote a view of transport systems that addresses problems of access and mobility for rural people to strengthen capacity of communities to control & manage transport facilities.
Figure 1: Piyasena uses his cycle trailer as a mobile mini store and kitchen. Hambamtota District, Sri Lanka. © Zul/Practical Action
Practical Action has worked on a range of transport technologies that address different transport needs, such as Ox carts, extended load carrying bicycles, aerial runways, bicycle taxis, bicycle ambulances, wheelbarrows, low cost wheelmaking, animal harnesses, low cost road construction and bicycle trailers. Cycle trailers are used for transporting goods, fuel, water and harvests where other means are too expensive.
Trailers allow people can now carry three times as much as with a bicycle, which allows people to carry around 200 kilograms (450 lbs.) The range of use is quite wide including ambulances, mobile shops, and even a mobile library in one instance in Sri Lanka, shown in figure 2.
Bicycle trailers
Bicycle trailers were developed within Practical Action South Asia (Sri Lanka) then adopted by Practical Action East Africa (Kenya) and now used in Nepal and Zimbabwe.
To make sure that the cycle trailer are affordable, Practical Action works with local partner organisations who operate credit schemes at low interest rates.
Figure 2: A cycle trailer used as a mobile library for school children in Sri Lanka © Zul/Practical Action
How to make a bicycle trailer
The cycle trailers are made in small village workshops from iron tubing, which is cut, bent, welded and drilled to make the frame and wheels. Modifications are also carried out to the trailers in these workshops at the request of the buyers.
Figure 3 shows one of the designs produced by Practical Action
The frame needs to be strong and rigid but as light as possible. Thin wall tube gives the best design but is not always available or affordable and some skill is needed to weld the thin material.
Details of the Frame Construction
Figure 4: The frame construction is made up from welded steel tube
The component parts to the frame design are listed in table 1
Table 1: Parts list for the bicycle trailer frame.
| Part No | Description | Qty | Material | Semi Finished Dimensions |
| 1 | Round Tube | 1 | Mild Steel |
|
| 2 | Square Tube | 2 | Mild Steel |
|
| 3 | Square Tube | 5 | Mild Steel |
|
| 4 | Square Tube | 6 | Mild Steel |
|
| 5 | Square Tube | 4 | Mild Steel |
|
| 6 | Square Tube | 2 | Mild Steel |
|
| 7 |
‘ |
6 | Mild Steel |
|
| 8 | Rod | 2 | Mild Steel |
|
| 9 | Wheel Mounting | 4 | Mild Steel |
|
| 10 | Plank | 2 | Wood | 873 x 126 x 15 |
| 11 | Hitch (Male) | 1 | Mild Steel | . |
| 12 | Round Tube | 1 | Mild Steel |
|
Alternative frame constructions can be used depending on materials and the production equipment available.
Figure 5 shows an alternative frame design made from tubular bar.
Figure 6 shows a frame that can be made from angle and bar
Hitch
Although hitching the trailer at the level of the rear axle has the least effect on the stability of the bicycle, hitching above the rear wheel (to the carrier or to the frame below the seat) is simpler and more compatible with duel use of the trailer as a handcart. This method has been widely tested on earth roads and tracks in various countries and has caused no problems for the trailer users. Various hitch mechanisms may be used, the requirement being that they are strong and durable and do not constrain relative movement between the bicycle and the trailer. The recommended mechanism is a rubber ball in a steel socket attached to the carrier or the rear wheel stays, but in some cases, the trailer has simply been tied to the carrier.
Figure 7: Hitch design. A steel or rubber ball drops into a socket formed from flat bar or cut from a pipe bolted to the carrier or frame of the bicycle
Wheels
Normal bicycle wheels are suitable only for rather light loads on many roads but are not robust enough for carrying heavy loads or for use on rough tracks. Strengthened wheels that take standard bicycle tyres have been developed for trailers.
References and further reading
This Howtopedia entry was derived from the Practical Action Technical Brief Bicycle Trailer.
To look at the original document follow this link: http://www.practicalaction.org/?id=technical_briefs_transport
• The Design of Bicycle Trailers Michael Ayre IT Publications 1986
• Low-cost Load-carrying Devices: The Design & Manufacture of Some Basic Means of Transport Ron Dennis and Alan Smith ITDG Publishing 1995
• Puncture Prevention Techniques for Low Cost Vehicles Michael Ayre & Alan Smith
• Cycle Trailers for India. Appropriate Technology Vol. 18 No 2
• Forum News. The International Forum for Rural Transport and Development A quarterly newsletter looking at the issues of transport with animal power, bridges, bicycles, gender and transport, financing, engineering, sustainable rural livelihoods, community planning. IFRTD’s address is shown below.
Useful contacts
I. T. Transport is a consultancy in transport for rural development.
I.T. Transport Ltd.
The Old Power Station
Ardington, Nr. Wantage
Oxon
OX12 8QJ
United Kingdom
Tel: +44 1235 833753 /821366
Fax: +44 1235 833753/821366
Website: http://www.ittransport.co.uk/
The International Forum for Rural Transport and Development is a global network of individuals and representatives from government, academia, multilateral and bilateral donor agencies, consultancies and technical institutions, national and international NGOs and groups of community organisations in 83 countries in Africa, Asia, Europe and North and
South America.
IFRTD Secretariat
2 Spitfire Studios
63-71 Collier Street
London, N1 9BE
United Kingdom
Tel: 44 20 7713-6699
Fax: 44 20 7713-8290
Website: http://ifrtd.gn.apc.org/
Community Bike Cart Design http://bikecart.pedalpeople.com/
Plans to build a wood and plywood cart using two bicycle wheels http://www.motherearthnews.com/DIY/1981-07-01/Dime-on-the-Dollar-Bicycle-Trailer.aspx (be sure to click on the photographs to display the illustrations).
Slide show of building bicycle cart using pre-drilled angle iron, plywood, bicycle wheels, and found material http://www.designcenter.umn.edu/service_engagement/projects/pdfs/YouthFarm.pdf
Internet addresses
World Bank
http://www.worldbank.org/html/fpd/transport/rural_tr/rts_imt.htm#patterns
The DFID transport site is managed by TRL (Transport Research Laboratory).
http://www.transport-links.org
Useful addresses
Practical Action
The Schumacher Centre for Technology & Development, Bourton on Dunsmore, RUGBY, CV23 9QZ, United Kingdom.
Tel.: +44 (0) 1926 634400, Fax: +44 (0) 1926 634401
e-mail:practicalaction@practicalaction.org.uk
web:www.practicalaction.org
